Upon completion, the participant should be able to properly apply the construction and inspection provisions of the AISC and RCSC Specifications regarding bolted connections, whether as an installer, supervisor, or inspector.
- Bolted Joints
- Bolting Materials
- Turn-of-Nut Method
- Twist-Off-Type Tension-Control Bolt Method
- Direct Tension Indicator Method
- Calibrated Wrench Method
- Bolting Inspection
Section 1. Bolted Joints
The purpose of this section is to explain and clarify the code requirements and the proper methods for specifying and using bolted joints. Following completion of this section, the participant should be able to understand the type of bolted joint specified for a specific connection, and to understand the installation and inspection requirements based upon the joint designation.
- Joint Types
- Shear/Bearing Load Transfer – Snug-Tightened and Pretensioned Joints
- Snug-Tightened Joints
- Pretensioned Joints
- Slip-Critical Joints
- Direct Tension Load Transfer
- Required Minimum Bolt Pretension – Pretensioned and Slip-Critical Joints
- RCSC Specification References
- Dimensions and Making of Bolt Holes
Section 2. Bolting Materials
The purpose of this section is to explain and clarify the code requirements and the proper methods for specifying bolts, nuts and washers as fastener assemblies in structural steel connections. Following completion of this section, the participant should be able to properly specify the type of bolting materials required for a project, identify these materials, control the material’s quality upon receipt, and select the proper materials for installation.
- Structural Fasteners
- Dimensions and Making of Bolt Holes
- Jobsite Storage
- Lubrication
- Requirements for Washers
- Bolt Stickout and Approximate Bolt Lengths
- Suitable Nuts for Structural Bolts
- Bolt Head Markings
- Manufacturer and Supplier Marks
- Dimensions of Structural Bolts
- Nut Markings and Dimensions for Structural Nuts
- Dimensions of ASTM F436 Washers
- Dimensions of ASTM F959 Direct Tension Indicators
Section 3. Turn-of-Nut Method
The purpose of this section is to explain and clarify the code requirements and the proper methods for specifying or performing bolt installation using the turn-of-nut method. Following completion of this section, the participant should be able to properly use high-strength bolts designated for turn-of-nut installation, perform pre-installation testing, snug the joint, install the fastener assembly, pretension the joint, and conduct visual inspection of the completed work.
- Pre-Installation Verification Testing Requirements
- Pre-Installation Verification – Turn-of-the-Nut Pretensioning Method when bolts are long enough to fit into the Skidmore-Wilhelm
- Pre-Installation Verification – Turn-of-the-Nut Pretensioning Method when bolts are too short to fit into the Skidmore-Wilhelm
- Required Minimum Bolt Pretension – Pretensioned and Slip-Critical Joints
- Pretensioning – Turn-of-Nut Method
- Inspection Procedure
- Lubrication
- Requirements for Washers
- Snug Tight Condition
- Systematic Tightening
- Bolt Stickout
- Reuse of Bolts Previously Pretensioned
- Required Rotation for Turn-of-Nut Method
Section 4. Twist-Off-Type Tension-Control Bolt Method
The purpose of this section is to explain and clarify the code requirements and the proper methods for specifying or performing bolt installation using the twist-off-type tension-control bolt method. Following completion of this section, the participant should be able to properly use high-strength bolts designated for twist-off installation, perform pre-installation testing, snug the joint, install the fastener assembly, pretension the joint, and conduct visual inspection of the completed work.
- Pre-Installation Verification Testing Requirements
- Pre-Installation Verification -Twist-Off-Type Tension-Control Bolt Pretensioning Method when bolts are long enough to fit into the Skidmore-Wilhelm
- Pre-Installation Verification – Twist-Off-Type Tension-Control Bolt Pretensioning Method when bolts are too short to fit into the Skidmore-Wilhelm
- Required Minimum Bolt Pretension – Pretensioned and Slip-Critical Joints (kips)
- Pretensioning – Twist-Off-Type Tension-Control Bolt Method
- Inspection Procedure – Twist-Off-Type Tension-Control Bolt Pretensioning Method
- Lubrication
- Requirements for Washers
- Snug-Tight Condition
- Systematic Tightening
- Bolt Stickout
- Reuse of Bolts Previously Pretensioned
- Determining the DTI Calibration for Pre-Installation Verification Tests when bolts are too short to fit into the Skidmore-Wilhelm
Section 5. Direct Tension Indicator Method
The purpose of this section is to explain and clarify the code requirements and the proper methods for specifying or performing bolt installation using the direct-tension-indicator method. Following completion of this section, the participant should be able to properly use high-strength bolts designated for direct-tension-indicator installation, perform pre-installation testing, snug the joint, install the fastener assembly, pretension the joint, and conduct visual inspection of the completed work.
- Pre-Installation Verification Testing Requirements
- Pre-Installation Verification – Direct Tension Indicator (DTI) Pretensioning Method when bolts are long enough to fit into the Skidmore-Wilhelm
- Pre-Installation Verification – Direct Tension Indicator (DTI) Pretensioning Method when bolts are too short to fit into the Skidmore-Wilhelm
- Required Minimum Bolt Pretension – Pretensioned and Slip-Critical Joints
- Pretensioning – Direct Tension Indicator Method
- Inspection Procedure – Direct Tension Indicator Method
- Lubrication
- Requirements for Washers
- Snug Tight Condition
- Systematic Tightening
- Bolt Stickout
- Reuse of Bolts Previously Pretensioned
Section 6. Calibrated Wrench Method
The purpose of this section is to explain and clarify the code requirements and the proper methods for performing high-strength bolt installation using the calibrated wrench method. Following completion of this section, the participant should be able to properly use bolts designated for calibrated wrench installation, perform pre-installation calibration and testing, snug the joint, install the fastener assembly, pretension the joint, and conduct visual inspection of the completed work.
- Pre-Installation Verification Testing Requirements
- Pre-Installation Verification – Calibrated Wrench Pretensioning Method when bolts are long enough to fit into the Skidmore-Wilhelm
- Pre-Installation Verification – Calibrated Wrench Pretensioning Method when bolts are too short to fit into the Skidmore-Wilhelm
- Required Minimum Bolt Pretension – Pretensioned and Slip-Critical Joints
- Pretensioning – Calibrated Wrench Method
- Inspection Procedure – Direct Tension Indicator Method
- Lubrication
- Requirements for Washers
- Snug Tight Condition
- Systematic Tightening
- Bolt Stickout
- Reuse of Bolts Previously Pretensioned
- Determining the DTI Calibration for Pre-Installation Verification Tests when bolts are too short to fit into the Skidmore-Wilhelm
Section 7. Bolting Inspection
The purpose of this section is to explain and clarify the code requirements for inspection, including the requirements for the individual elements of the bolted connections (holes, bolting materials, faying surfaces), observation of the project operations and the installation methods, and the arbitration of disputes should they arise. Following completion of this section and the prior sections, the participant should be able to properly apply the construction and inspection provisions of the AISC and RCSC Specifications regarding bolted connections, whether as an installer, supervisor, or inspector.
- Principles of Bolting Inspection
- Bolt Holes
- Bolt Head Markings
- Bolt Manufacturer and Supplier Marks
- Nut Markings
- Jobsite Storage
- Pre-Installation Verification Testing Requirements
- Lubrication
- Requirements for Washers
- Systematic Tightening
- Snug-Tightened Joints
- Required Minimum Pretension – Pretensioned and Slip-Critical Joints
- Inspection Procedure – Turn-of-Nut Pretensioning Method
- Inspection Procedure – Twist-Off Type Tension-Control Bolt Pretensioning Method
- Inspection Procedure – Direct Tension Indicator Method
- Inspection Procedure – Calibrated Wrench Pretensioning Method
- Bolt Stickout
- Reuse of Bolts Previously Pretensioned
- Arbitration of Disputes – when bolts are long enough to use a Skidmore-Wilhelm
- Arbitration of Disputes -when bolts are too short to use a Skidmore-Wilhelm
- Determining the DTI Calibration